ＴＡ０８Ｅ０００００００００Ｊ２００１ＡＢＡＴ００
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) (If body maintenance is required)
The Accord SRS includes a driver’s airbag in the steering wheel hub, a passenger’s airbag in the dashboard above the
glove box, seat belt tensioners in the front seat belt retractors, seat belt outer lap tensioners in the front seat belt lower
anchor, side curtain airbags in the sides of the roof, and side airbags in the front seat-backs. Information necessary to
safely service the SRS is included in this Shop Manual. Items marked with an asterisk ( ) on the contents page
include or are located near SRS components. Servicing, disassembling, or replacing these items requires special
precautions and tools, and should be done by an authorized Honda dealer.
• To avoid rendering the SRS inoperative, which could lead to personal injury or death in the event of a severe frontal
or side collision, all SRS service work should be done by an authorized Honda dealer.
• Improper service procedures, including incorrect removal and installation of the SRS, could lead to personal injury
caused by unintentional deployment of the airbags, side airbags, and/or side curtain airbags.
• Do not bump or impact the SRS unit, front impact sensors, or side impact sensors, or rear safing sensor when the
ignition switch is ON (II), or for at least 3 minutes after the ignition switch is turned to LOCK (0); otherwise, the
system may fail in a collision, or the airbags may deploy.
• SRS electrical connectors are identified by yellow color coding. Related components are located in the steering
column, front console, dashboard, dashboard lower panel, in the dashboard above the glove box, in the front seats,
in the roof side, and around the floor. Do not use electrical test equipment on these circuits.
07/09/20 19:31:50 62TA000B_200_0001
ＴＡ０８Ｅ０００００００００Ｊ２００１ＺＣＡＴ００
Body
Doors
Mirrors
Glass
Sunroof
Interior Trim
Consoles
Dashboard
............................................................................................Special Tools . 20-2
......................
....

.....
....
..................
...........................................
...........................................
...........................................
...........................................
..
.....
.............................
........................
...........................
Component Location Index . 20-3
Front Door Panel Removal/Installation . 20-12
Front Door Outer Handle Replacement . 20-19
Front Door Latch Replacement . 20-23
Front Door Glass and Regulator
Replacement . 20-26
Front Door Sash Inner Trim
Replacement . 20-29
Front Door Sash Outer Trim
Replacement . 20-31
Front Door Glass Outer Weatherstrip
Replacement . 20-31
Front Door Outer Molding
Replacement . 20-33
Front Door Weatherstrip Replacement . 20-34
Rear Door Panel Removal/Installation . 20-35
Rear Door Outer Handle Replacement . 20-38
Rear Door Latch Replacement . 20-40

...........................................
....
......................
......................
......................
..........................
...........................................
....
......................
......................
Component Location Index . 20-61
Windshield Replacement . 20-63
Rearview Mirror Harness Cover Base
Replacement . 20-68
Rain Sensor Cover Base Replacement . 20-69
Rear Window Replacement . 20-70
Quarter Glass Replacement . 20-79
......................
............
.......................
....................................
............
....................
.....................
............................
...................................
.......
...........................................
..
......................

..
.....
.................
...........
................
..................................
......................
..
.............
..................
.....................................
....................................
..
.....
.................
...........
................
..................................
Component Location Index . 20-98
Trim Removal/Installation - Door Areas . 20-101
Trim Removal/Installation - Pillar Areas
- Without Side Curtain Airbags . 20-105
Trim Removal/Installation - Pillar Areas
- With Side Curtain Airbags . 20-108
Trim Removal/Installation
- Rear Side Area . 20-124
Trim Removal/Installation
- Rear Shelf Area . 20-125
Trim Removal/Installation - Trunk Area . 20-128
Trim Removal/Installation - Trunk Lid . 20-128

..............................
..............................
...
...............
...............
..............................
..............................
..............................
..............................
..............................
..............................
........
..............................
.....................
....
..............................
.......
..............................
..............................
..............................
.........
..............................
..............................
..............................
...
...............
...............
..............................
..............................
..............................

Side Defogger Vent Trim
Removal/Installation . 20-178
Driver’s Outer Middle Pad
Removal/Installation . 20-178
Driver’s Inner Middle Pad
Removal/Installation . 20-179
Passenger’s Middle Pad
Removal/Installation . 20-179
Column Cover Removal/Installation . 20-180
Dashboard/Steering Hanger Beam
Removal/Installation . 20-182
Dashboard/Steering Hanger Beam
Disassembly/Reassembly . 20-188
07/09/20 19:31:51 62TA000B_200_0002
Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior Trim
Fenderwell
Openers
Frame
......................
...............................................
...............
...
...........................................
......
.......

..............
...........................................
.....
...........................................
........
...........................................
...
Component Location Index . 20-191
Front Seat Active Head Restraint
Inspection . 20-193
Front Seat Removal/Installation . 20-194
Front Seat Recline Motor Replacement . 20-200
Front Seat Lumbar Support
Replacement . 20-201
Front Seat Slide Motor Replacement . 20-203
Front Seat Slide Lever Replacement . 20-206
Front Seat Torsion Bar Replacement . 20-207
Rear Seat Access Cable Replacement . 20-208
Front Seat Frame Replacement . 20-209
Front Seat-back Cover Replacement . 20-214
Front Seat Cushion Cover
Replacement . 20-224
Rear Seat Removal/Installation . 20-236
Rear Seat-back Latch Replacement . 20-239
Rear Seat-back Release Lever/Cable
Removal/Installation . 20-240
Rear Seat Armrest Replacement . 20-241
Trunk Pass-through Lid Lock Cylinder
Replacement . 20-242
Trunk Pass-through Lid Replacement . 20-243

............
Hood Adjustment . 20-260
Hood Seal Replacement . 20-261
Hood Insulator Replacement . 20-262
Hood Support Strut Replacement . 20-262
................................
........
......
..............
...........................................
................................
........
......
..............
...........................................
Trunk Lid Adjustment . 20-263
Trunk Lid Torsion Bar Replacement . 20-264
Trunk Lid Weatherstrip Replacement . 20-265
Trunk Lid Cushion Replacement . 20-265
Trunk Lid Dynamic Damper
Replacement . 20-266
.........................
................
.........................
................
Fuel Fill Door Adjustment . 20-267
Fuel Cap Adapter Replacement . 20-268
...............
..........................
..............

..........
..
.............
...............
....................
Front Inner Fender Replacement . 20-288
Front Splash Shield Replacement . 20-289
Front Fender Fairing Replacement . 20-290
Middle Floor Undercover Replacement . 20-291
Fuel Pipe Protector Replacement . 20-292
Rear Inner Fender Replacement . 20-292
Rear Air Outlet Replacement . 20-293
......................
............
..................
..........................
.........
...........................................
...................
......................
............
..................
..........................
.........
...........................................
...................
Component Location Index . 20-294
Hood Opener Cable Replacement . 20-295
Trunk Lid Opener Cable/Fuel Fill Door
Opener Cable Replacement . 20-297

070AG-SJAA10S Frame Positioning Guide Pin 1
07/09/20 19:31:51 62TA000B_200_0004
＊０１
ＴＡ０８Ｅ１４Ｊ１６１２６７０００００ＤＡＡＴ００
2-door
20-3
Doors
Component Location Index
FRONT PULL
POCKET CAP
ARMREST
SWITCH PANEL
POWER WINDOW SWITCH
ORNAMENT PANEL
GRIP BASE
FRONT DOOR
PANEL CAP
POWER MIRROR
SWITCH
DOOR GLASS INNER
WEATHERSTRIP
Passenger’s side
SWITCH PANEL
POWER WINDOW SWITCH
DOOR PANEL
UPPER
GRIP
BRACKET
LOWER GRIP
BRACKET

GLASS
IMMOBILIZER and
SECURITY LABEL
REGULATOR
CENTER LOWER CHANNEL
OUTER
HANDLE
COVER
OUTER HANDLE SEALS
OUTER HANDLE BASE
LOCK CYLINDER
(Driver’s)
STRIKER
LATCH
INNER HANDLE CABLE
INNER HANDLE
LATCH CABLE
OUTER HANDLE
FRONT LOWER CHANNEL
GLASS RUN CHANNEL
INNER HANDLE CAP
LATCH PROTECTOR
Passenger’s side
OUTER HANDLE HOLDER
Replacement, page 20-26
Adjustment, page 20-50
Replacement, page 20-26
Adjustment, page 20-53
Replacement, page 20-23
Replacement, page 20-19

OUTER WEATHERSTRIP
HINGE
HINGE
DOOR
CHECKER
DOOR
DOOR WEATHERSTRIP
SPEAKER
PLASTIC COVER
(cont’d)
Replacement, page 20-30
Replacement, page 20-31
Replacement, page 20-33
Replacement, page 20-31
Position Adjustment, page 20-51
Replacement, page 20-34
07/09/20 19:31:57 62TA000B_200_0009
＊０３
4-door Front door (cont’d)
20-8
Doors
Component Location Index (cont’d)
GLASS
IMMOBILIZER and
SECURITY LABEL
REGULATOR
CENTER LOWER CHANNEL
OUTER
HANDLE
COVER

ORNAMENT PANEL
DOOR GLASS INNER
WEATHERSTRIP
SWITCH PANEL
DOOR PANEL
ASHTRAY
(cont’d)
Removal/Installation, page 20-35
07/09/20 19:31:59 62TA000B_200_0011
＊０２
4-door Rear door (cont’d)
20-10
Doors
Component Location Index (cont’d)
DOOR SASH INNER TRIM
DOOR OUTER MOLDING
DOOR GLASS
OUTER WEATHERSTRIP
HINGE
HINGE
DOOR
CHECKER
DOOR
DOOR WEATHERSTRIP
PLASTIC COVER
DOOR SASH OUTER TRIM
Replacement, page 20-45
Replacement, page 20-48
Replacement, page 20-47
Position Adjustment, page 20-51

page 20-53
Replacement, page 20-40
Replacement, page 20-38
Replacement, page 20-285
Replacement, page 20-42
07/09/20 19:32:03 62TA000B_200_0013
＊０１
＊０２
＊０３
＊０４
ＴＡ０８Ｅ１４Ｊ１６１２６７２１４０１ＫＤＡＴ００
2-door
20-12
Doors
Front Door Panel Removal/Installation
A
B
Fastener Locations
:Screw,2A:Screw,1B
A
B
A
C
Fastener Location
:Screw,1
A
Fastener Location
:Screw,1
A
B

20-13
Fastener Locations
:Clip,10
(Gray)
A
B
C
D
A
B
C
C
A
B
A
B
C
D
E
F
G
8. Remove the door panel (A) with as little bending as
possible to avoid creasing or breaking it.
–1 Start at the bottom edge of the door panel,
release the clips with a commercially available
trim pad remover.
–2 Detach the upper clips.
–3 Starting at the rear, pull the door panel upward.
NOTE: The inner handle cable (B) and the latch
cable (C) are connected to the inner handle (D).

D
D
D
Fastener Locations
:Screw,4 :Clip,3
Fastener Locations
:Screw,2A:Scerw,3B:Screw,1C
A
B
C
D
E
F
A
B
B
12. Remove the ornament panel (A).
–1 Remove the screws from back of the door
panel (B).
–2 Release the hooks (C) from back of the door
panel.
–3 Detach the hooks (D) and the clips from the
grip base (E).
13. Remove the screws (A, B, C), then remove the grip
base (D) and the upper grip bracket (E) from the
door panel (F).
07/09/20 19:32:05 62TA000B_200_0016
＊１１
＊１２
＊１３

removal, and note these items:
• If the clips are damaged or stress-whitened,
replace them with new ones.
• Replace any damaged cable fasteners with new
ones.
• The latch cable (A) should be fixed to the cable
fastener (B) with the latch in the unlocked
position as shown.
• Make sure the connectors are plugged in
properly, and the cables are connected securely.
• Make sure the window and power door lock
operate properly.
• When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
07/09/20 19:32:05 62TA000B_200_0017
＊０１
＊０２
＊０３
＊０４
ＴＡ０８Ｅ１３Ｊ１６１２６７２１４０１ＫＤＡＴ０１
4-door
20-16
Doors
Front Door Panel Removal/Installation (cont’d)
A
B
Fastener Locations
:Screw,2
A

–3 Starting at the rear, pull the door panel upward.
NOTE: The inner handle cable (B) and the latch
cable (C) are connected to the inner handle (D).
Do not pull the door panel up too far, or these
cables will be damaged.
07/09/20 19:32:06 62TA000B_200_0018
＊０５
＊０６
＊０７
＊０８
20-17
A
B
C
C
A
B
C
D
E
F
A
B
C
D
E
F
G
Fastener Location
:Clip,1

all of the hooks (C).
–3 Pull the switch panel rearward to release the
front hook (D).
(cont’d)
07/09/20 19:32:07 62TA000B_200_0019
＊０９
＊１０
＊１１
20-18
Doors
Front Door Panel Removal/Installation (cont’d)
Fastener Locations
:Screw,5
A
B
C
Fastener Locations
:Screw,6
A
B
C
D
E
C
B
D
46.5 mm (1.83 in.)
A
B
11. Remove and loosen the screws from back of the

4-door
20-19
Front Door Outer Handle Replacement
A
B
C
D
B
A
B
C
D
A
B
NOTE: Put on gloves to protect your hands.
1. Remove the door panel:
• 2-door (see page 20-12)
• 4-door (see page 20-16)
2. Disconnect the power door lock actuator connector
(A), and detach the harness clips (B).
3. Remove the rear plug cap (C), then remove the
plastic cover (D) as needed.
NOTE: Remove the glue from the door surface. If
the plastic cover is damaged or torn, replace it.
4. Remove the maintenance cap (A) (2-door) or the
hole seal (B) (4-door).
(cont’d)
07/09/20 19:32:08 62TA000B_200_0021
＊０５
＊０６

＊１０
Driver’s door
Passenger’s door
Driver’s door
Passenger’s door
20-21
Fastener Location
:Bolt,1
A
B
B
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
Fastener Location
:Bolt,1
A
B
B
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
D
A
C
D
7. While holding the outer handle cover (A) from
outside of the door, loosen the bolt (driver’s door)

:Nut,1
A
B
C
D
E
6x1.0mm
4.9 N·m
(0.5 kgf·m,
3.6 lbf·ft)
C
9. Driver’s door: If the retainer (A) of the lock cylinder
cable (B) is damaged, release the hooks (C), then
replace it.
10. Pull the outer handle (A) back, and out as shown to
remove it from the door. Take care not to scratch
the door.
11. Release the hooks (A, B), then remove the outer
handle front seal (C) and the outer handle rear seal
(D).
12. Remove the outer handle base (A).
–1 Detach the rod fastener (B).
–2 With a clip remover, disconnect the outer
handle rod (C).
–3 Loosen the nut.
–4 Release the hook (D), and slide the outer
handle base forward to release the special bolt
(E) from the door panel.
07/09/20 19:32:10 62TA000B_200_0024
＊１５

1. Remove the door panel and the inner handle:
• 2-door (see page 20-12)
• 4-door (see page 20-16)
2. Remove the plastic cover as needed (see step 2 on
page 20-19).
3. Detach the rod fastener, and disconnect the outer
handle rod from the outer handle base (see step 12
on page 20-22).
4. Driver’s door: Disconnect the cylinder cable from
the latch (see step 5 on page 20-20).
5. 2-door: Pull the glass run channel away as needed,
and remove the bolt, then remove the center lower
channel by pulling it downward (see step 6 on page
20-20).
6. 4-door: Pull the glass run channel (A) away as
needed, and remove the bolt, then remove the
center lower channel (B) by pulling it downward.
(cont’d)
Replace.
07/09/20 19:32:10 62TA000B_200_0025