2374

IEEE TRANSACTIONS ON MAGNETICS, VOL. 45, NO. 6, JUNE 2009

Sensitivity Dependence of the Planar Hall Effect Sensor on the
Free Layer of the Spin-Valve Structure
T. Q. Hung1 , S. J. Oh1 , B. D. Tu2 , N. H. Duc2 , L. V. Phong1 , S. AnandaKumar1 , J.-R. Jeong1 , and C. G. Kim1
Department of Materials Science and Engineering, Chungnam National University, Daejeon 305-764, Korea
Department of Nano Magnetic Materials and Devices, Faculty of Physics Engineering and Nanotechnology,
College of Technology, Vietnam National University, Hanoi, Vietnam
Planar Hall effect (PHE) sensors with the junction size of 50 m 50 m were fabricated successfully by using spin-valve thin films
Ta(5)/NiFe( )/Cu(1.2)/NiFe(2)/IrMn(15)/Ta(5) (nm) with = 4 8 10 12 16. The magnetic field sensitivity of the PHE sensors increases with increasing thickness of ferromagnetic (FM) free layer. The sensitivity of about 95.5 m
/(kA/m) can be obtained when
the thickness of the FM-free layer increases up to 16 nm. The enhancement of sensitivity is explained by the shunt current from other
layers. The PHE profiles are well described in terms of the Stoner–Wohlfarth energy model. The detection of magnetic micro-beads label
Dynabeads® M-280 is demonstrated and the results revealed that the sensor is feasible for high-resolution biosensor applications.
Index Terms—Biosensor applications, high field sensitivity, micro-beads detection, planar Hall effect.

I. INTRODUCTION
AGNETORESISTIVE biosensors have attracted a lot
of attention [1] because of their numerous advantages
such as an easy-to-use, highly portable sensing platform with
high sensitivity and faster read out technique [2]. Among the
various kinds of magnetoresistive biosensors, the planar Hall
effect (PHE) sensor has vast potential used in nano-Tesla field
range detection sensors and biosensors due to its extremely high
signal-to-noise ratio, high linearity at low field range, and high
field sensitivity [3].
PHE, known as anisotropic magnetoresistance (AMR), is induced from spin-orbit coupling and spin polarization of the materials. Alternatively, NiFe permalloy was chosen to develop the
high field sensitivity PHE sensor. Dau et al. [4] found that the
PHE sensor using single NiFe layer was able to reduce thermal

high-sensitivity, is highly desirable from both fundamental and
application point of views. There were several reports disclosing
the enhancement of the sensitivity of a sensor based on spinvalve structure such as changing the applied field direction [8],
[9] and developing the spin-valve structure with the uniaxial
field normal to the unidirectional field [10], [11]. For the first
case, the PHE sensor has maximum sensitivity when the applied
field direction is parallel to the easy axis of the thin film; unfortunately, a hysteresis of the PHE profile was observed. For
the second case, when there is a tilt angle between the uniaxial and unidirectional fields, the coherent rotation of FM-free
layer in the applied fields no longer exists. These deteriorate
the signal-to-noise ratio of the sensors as it gives possibility for
bio-applications.
To obtain high sensitivity sensors while avoiding the above
disadvantages, we optimized the thicknesses of the other layers,
increased FM-free layer in the spin-valve structure and studied
the role of PHE in these thin films systematically. The experimental results revealed that the sensitivity of the sensors increases due to the increased thickness of the FM-free layer. The
sensitivity of about 95.5 m /(kA/m) can be obtained as the
thickness of FM-free layer increases up to 16 nm.
II. EXPERIMENTAL PROCEDURE
A. Sensors Fabrication
The cross-junction sensors with the junction size of
50 m 50 m were prepared on SiO substrate using lift off
method. Firstly the cross junctions sized 50 m 50 m were
stenciled out on the photoresist coated on silicon dioxide wafer,
The spin-valve thin films Ta(5)/NiFe /Cu(1.2)-/NiFe(2)/
(nm), were deposited on
IrMn(15)/Ta(5),

0018-9464/$25.00 © 2009 IEEE



TABLE I
THE PARAMETERS: INTERLAYER COUPLING (H ), EFFECTIVE ANISOTROPY
CONSTANT (K ), SATURATE MAGNETORESISTANCE (M ), MAXIMUM
PHE VOLTAGE (V ), AND FIELD SENSITIVITY (S ) OF THE SENSORS USING
SPIN-VALVE THIN FILMS WITH DIFFERENT FREE LAYER THICKNESSES (x)

B. Sensor Characterization
Fig. 1 shows the SEM image of the passivated single sensor
junction 50 m 50 m. The terminals - represent the current line and - represent the voltage line. The unidirectional
anisotropy field,
, and/or the uniaxial anisotropy field of the
thin film is aligned parallel to the long terminals - . The PHE
profiles were measured by the electrodes bar - with a sensing
current of 1 mA applied through the terminals - and under
the external magnetic fields ranging from 4 kA/m to 4 kA/m
applied perpendicular to the direction of the current line. The
induced output voltages of cross-junctions were measured by
means of a Keithley 2182A Nanovoltmeter with a sensitivity
of 10 nV. All these sensor characterizations were carried out at
room temperature. To detect the magnetic beads, we performed
the magnetic drop and wash experiments on the sensor junction with 1 l solution 0.1% of the Dynabeads® M-280 by using
the micro pipette-lite SL-10 under an applied magnetic field of
550 A/m and a sensing current of 1 mA.
III. RESULTS AND DISCUSSION
Fig. 2 shows the PHE profiles of the sensor junctions with
various free layer thicknesses are characterized as a function of
external magnetic fields in the range from 4 kA/m to 4 kA/m.
, show linearly response
These PHE voltage profiles,
at small fields, reach the maximum voltage at about their inter, and finally decrease with a further



2376

IEEE TRANSACTIONS ON MAGNETICS, VOL. 45, NO. 6, JUNE 2009

where
, and are the thickness, uniaxial anisotropy
constant, saturation magnetization of the thin film and interlayer
coupling energy, respectively. is the angle between the external magnetic field and easy axis of thin film and is the angle
between the unidirectional field and the easy axis of the FM-free
and
.
layer. In our experimental conditions
For the FM-free layer, the PHE output voltage is described by
Ohm’s law and could be given by [14]

(2)
where
and
, and are the current applied to the
sensor junction, thickness, transverse and longitudinal resistivity, and angle between the magnetization direction of the
, of the thin film,
FM-free layer and unidirectional field,
respectively.
The angle can be calculated from the minimum energy condition of the above Stoner-Wohlfarth equation at each value of
applied magnetic fields. Hence, the PHE voltage profile can then
be calculated from (2). The calculated results presented as solid
mA;
lines in Fig. 2 are obtained for the best fit with

surface. The aggregation of the magnetic beads occurs at the
drying stage. That is, after dropping the bead solution on the
sensor surface, it needs some time to dry. The first step changes
of the signals are assumed to be due to the viscous flow motion

Fig. 3. Real-time profile of the highest field sensitivity PHE sensor under an
applied magnetic field of 550 A/m and with the sensing current of 1 mA.

for stabilization as well as the Brownian motion of the beads.
When the solution dries, the beads rearrange. During this time,
some beads aggregate and become clusters on the sensor surface. This lessens the total stray field on the sensor surface and
hence, the second step changes in the second and third cycles
were observed in the real-time profile.
For further understanding the micro-bead detection using
PHE sensor, it is noted that the magnetization of the magnetic
sphere is purely a dipole at the center of the sphere with a
at a distance identified by [3]
magnetic field

(3)
and
are the value and vector in the direction of
where
magnetization of the bead, respectively. and are the bead
radius and distance from the center of the bead to the observation
point, respectively.
The stray field of a single bead on the sensor surface could be
crudely calculated by [16]

(4)

clearly shown in the first cycle, the number of beads on the
sensor surface is estimated to be small, and the distance among
beads on the sensor junction is far enough to avoid the effect
from the rearrangement of beads during the drying stage. In
the second and third cycles, the number of magnetic beads on
the sensor junction are larger; they easily aggregate to become
clusters under applied magnetic field due to short bead-bead
distance.
IV. CONCLUSION
We enhanced the field sensitivity of PHE sensors by increasing the free layer in the spin-valve structure Ta(5)/NiFe /
Cu(1.2)/NiFe(2)/IrMn(15)/Ta(5) (nm). The maximum sensitivity of the fabricated sensors of about 95.5 m /(kA/m) can
be obtained as the thickness of the free layer increases up
to 16 nm. The detecting Dynabeads® M-280 results with the
highest sensitivity PHE sensor reveals that our sensor is very
sensitive in identifying the existence of magnetic beads; different number of magnetic beads give different changes in the
real-time profile. Moreover, the decrease in stray field occurred
due to the bead-bead interaction at the drying stage, which can
be recognized by a two step-type of the real-time profile.
ACKNOWLEDGMENT
This work was supported by KOSEF under project
M10803001427-08M0300-42710, the Fundamental R&D
Program for Core Technology of Materials funded by the
Ministry of Knowledge Economy, Republic of Korea. The
work of J.-R. Jeong was supported by the Korea Research
Foundation (KRF-2008-331-D00234). The work of N. H. Duc
was supported by Vietnam National University, Hanoi under
project QG.TD 07.10.

2377


[11] Z. Q. Lu, G. Pan, and Y. K. Zheng, “Spin valves with canted pinning
field,” J. Appl. Phys., vol. 91, pp. 2161–2164, Oct. 2002.
[12] B. Dieny, V. S. Speriosu, S. S. Parkin, B. A. Gurney, D. R. Wilhoit, and
D. Mauri, Phys. Rev. B, vol. 43, pp. 1297–1300, Jan. 1991.
[13] B. D. Tu, L. V. Cuong, T. Q. Hung, D. T. H. Giang, T. M. Danh,
N. H. Duc, and C. G. Kim, “Optimization of spin-valve structure
NiFe/Cu/NiFe/IrMn for planar Hall effect based biochips,” in AMC
Conf., Busan, Korea, 2008.
[14] R. C. O’Handley, Modern Magnetic Materials: Principles and Applications. New York: Wiley, 2000.
[15] B. Dieny, “Classical theory of giant magnetoresistance in spin-valve
multilayers: Influence of thicknesses, number of periods, bulk and interfacial spin-dependent scattering,” J. Phys: Condens. Matter., vol. 4,
pp. 8009–8020, Oct. 1992.
[16] L. Ejing, M. F. Hansen, and A. K. Menon, “Planar Hall effect magnetic
sensor for micro-bead detection,” in Conf. Proc., Eurosensors 2003,
Sept. 2003, pp. 1095–1098.
[17] [Online]. Available: />112.05D06D%20602.10%20Dynabeads%20M280%20Streptavidin%
20(rev%20012).pdf